FREE EXPEDITED SHIPPING ON ORDERS OVER $150 IN CANADA!


Featured

Genuine E3D V6 Gold HotEnd (12V)

Genuine E3D V6 Gold HotEnd (12V)

To celebrate the E3D V6’s third anniversary we wanted to do something special to show off the HotEnd..

$139.99 CAD

Genuine E3D V6 Gold HotEnd (24V)

Genuine E3D V6 Gold HotEnd (24V)

To celebrate the E3D V6’s third anniversary we wanted to do something special to show off the HotEnd..

$139.99 CAD

Smoothieboard 5xC v1.1

Smoothieboard 5xC v1.1

The Smoothie project is about creating an open source platform for controlling digital fabrication m..

$199.99 CAD

Smoothieboard 4XC v1.1

Smoothieboard 4XC v1.1

The Smoothie project is about creating an open source platform for controlling digital fabrication m..

$169.99 CAD

BLTouch : Auto Bed Leveling Sensor Probe (April 2017 "Smart" Edition)

BLTouch : Auto Bed Leveling Sensor Probe (April 2017 "Smart" Edition)

BLTouch is an auto leveling Z sensor probe for 3D Printers based on open-source such as Delta or Car..

$39.99 CAD

.9deg Nema 17 Bipolar Stepper Motor 44Ncm(62.3oz.in) 17HM19-1684S

.9deg Nema 17 Bipolar Stepper Motor 44Ncm(62.3oz.in) 17HM19-1684S

This is high precision bipolar Nema 17 stepper motor with 0.9° step angle (400 steps/revol..

$29.99 CAD

1.8deg Nema 17 Bipolar Stepper Motor 2A 45Ncm(64oz.in) 17HS16-2004S

1.8deg Nema 17 Bipolar Stepper Motor 2A 45Ncm(64oz.in) 17HS16-2004S

This is high torque Nema 17 stepper motor with 1.8° step angle (200 steps/revolution). Eac..

$29.99 CAD

Nema 17 Bipolar Pancake Stepper Motor 3.5V 1A 13Ncm(18.4oz.in) 17HS08-1004S

Nema 17 Bipolar Pancake Stepper Motor 3.5V 1A 13Ncm(18.4oz.in) 17HS08-1004S

This is Short Height Bipolar Nema 17 stepper motor with 1.8° step angle (200 steps/revolut..

$19.99 CAD

Bestsellers

PTFE Bowden Tubing (100mm) (1.75mm Filament)

PTFE Bowden Tubing (100mm) (1.75mm Filament)

The tubing used is a specially selected PTFE fluoro-polymer that has superior properties for use in ..

$0.75 CAD

E3D Capricorn Bowden Tubing (100mm)

E3D Capricorn Bowden Tubing (100mm)

Your extruder system has a finite amount of pushing force. You want as much as possible of that push..

$1.99 CAD

BLTouch : Auto Bed Leveling Sensor Probe (April 2017 "Smart" Edition)

BLTouch : Auto Bed Leveling Sensor Probe (April 2017 "Smart" Edition)

BLTouch is an auto leveling Z sensor probe for 3D Printers based on open-source such as Delta or Car..

$39.99 CAD

LM2596 Adjustable DC-DC Buck Converter Step Down Voltage Regulator

LM2596 Adjustable DC-DC Buck Converter Step Down Voltage Regulator

DescriptionChip: LM2596SInput Voltage: 3V - 35V (must be at least 1.5V higher then output)Output Vol..

$4.99 CAD

Latest

E3D v6 Threaded Heatsink

E3D v6 Threaded Heatsink

An alternative to GroovemountThere are a couple of major flaws with groovemounting (or previous stan..

$24.99 CAD

NEMA 17 Mounting Bracket (METAL)

NEMA 17 Mounting Bracket (METAL)

NEMA 17 Mounting L  Bracket.  Metal..

$3.49 CAD

BLTouch Extension Cable 1.5m
E3D Groove Mount Bowden Adaptor - 1.75mm Filament (4mm OD Tubing)

E3D Groove Mount Bowden Adaptor - 1.75mm Filament (4mm OD Tubing)

This is a neat little solution for quickly and easily converting a direct extruder that would normal..

$7.99 CAD

Latest Articles - All Articles

The MKS TFT32 is a fantastic self-contained controller which, among others, can control the Smoothieboard via the serial interface.  The connection method is fairly easy but will require a couple manual hardware and setting configurations. 1.        The cable that comes with the MKS TFT32 will need to have the 8 pin connector removed on one end and replaced with a 6 pin straight connector matched pin for pin with the 6 pin serial pins on the Smoothieboard.  Make sure that the TX on the MKS TFT32 goes to the RX on the Smoothieboard and v..
Your guide to installing Smoothieboard in a 3D printerBLTouch ManualE3D Online DocumentationHow to Connect MKS TFT to Smoothieboard..
What Kind of Nozzle Should I Use?
The most common nozzle used in 3D printers today is no doubt the 0.4mm brass nozzle.  This works fine for the basic filaments like ABS, PLA, ASA, and PETG and many others.  But, there are more exotic filaments out there that are much more abrasive than these filaments and will very quickly wear down the tiny hole in your brass nozzle, causing it to become enlarged and misshapen which will progressively degrade the quality of your 3D prints.  These other filaments include filaments such as carbon fiber, wood fiber, filament containing metallic particles and so on.  So, if yo..
Many 3D printer enthusiasts may be for the first time diving into electronics tinkering.  The electronics landscape is very different today than it was 30 years ago.  Today we have micro-controllers and breakout boards and a lot of the harder design work is already done for you.    But the fundamentals themselves have not changed.Choosing the correct wire size for your 3D printer's motors, hotend, heat bed and sensors is very important.  It is not always one size fits all.Let's compare a wire to a water pipe for a moment.  A water pipe carries a certain volume of ..
0 comments on this article - view comments